WAGNER Project 115 Owner's Manual download pdf (Page 9)

Assembly

Figure 2 - Assembling the Wheels

1. Slide the spacer (a), the wheel (b) and the push nut (c) over the

end of the axle in the order shown. Make sure the spacer (a) is

oriented so the lipped side will face toward the middle of the

axle.

You will need to stand the axle vertically on a at and

stable surface to assemble the wheels.

 2. Lightlytaptheassemblyaid(d)withamallettosecurethe

push nut (c) over the end of the axle. Repeat steps for other

wheel.

Figure 3 - Assembling the Axle

1. Slide both ends of the axle up into the slots (a) as shown. The

lipped side of the spacers (b) should go inside of the axle

slots.

2. Make sure each axle plate is oriented and located as shown (L

and R). Secure each plate with two (2) screws. Snap the wheel

caps (e) over the ends of the push nuts.

Figure 4 - Assembling the Handle

1. To assemble the handle, press the button (a) as shown and

slidethehandleintothecartassembly.

 2. Oncethehandleisfullyinsidethecart,releasethebuttonand

pull the handle until it locks in up or down position.

Figure 5 - Attaching the Hose

 1. Screwthethreadofthehigh-pressurehoseontothespray

hose connection. Tighten with an adjustable wrench.

 2. Threadtheotherendofthehosetothespraygun.

Gripthespraygunwithanadjustablewrenchonthehandle,

and tighten the hose nut with the other.

The spray tip should not be attached until after the

sprayer and spray hose have been purged and primed.

Before You Begin

Figure6-LockingtheSprayGun

Danger

Always lock the trigger o when attaching the spray

tip or when the spray gun is not in use.

1. The gun is secured when the trigger lock is at a 90° angle

(perpendicular) to the trigger in either direction.

Figure 7 - Pressure Relief Procedure

Danger

Be sure to follow the Pressure Relief Procedure

when shutting the unit o for any purpose. This

procedure is used to relieve pressure from the spray

hose.

 1. Lockthesprayguno.FliptheON/OFFswitchtotheOFF

position.

2. Turn the PRIME/SPRAY knob to PRIME.

Take care not to pinch your ngers when turning the

switch.

 3. Unlockthespraygunandtriggerspraygunintothesideof

thematerialbucket.Lockthespraygun.

Figure8-Removing/EmptyingtheHopper

Make sure your oors and furnishings are protected

with drop cloths to avoid property damage.

Always place the hopper on a hard, at, stable surface

when removed.

1. Perform Pressure Relief Procedure.

2. Pull the return tube (a) from the rear of the hopper lid.

 3. Grabhopperbythesidehandles(b)andgentlypullitout.

 4. Whennishedemptying/cleaning,replacehopperand

hopper lid.

 5. Replacethereturntubebyinsertingitthroughthenotchin

the hopper lid.

Danger

The hopper can be heavy when lled with spraying

material. Make sure to lift with your legs and not

your back in order to reduce the risk of injury.

Purging and Priming

Figure9-PrimingtheSprayer

1. Pull the return tube from the hopper and hold it over a waste

container.

 2. TurnthePRIME/SPRAYknobtoPRIME.Pluginthesprayer.

PresstheON/OFFswitchintotheONposition(I).

Any uids remaining in the pump and the return tube

will ow out of the return tube. Let the pump run until

no uid is coming from the return tube.

 3. SwitchthepumptoOFF.Removethereturntubefromthe

waste container and insert it into the notch in the hopper lid.

 4. Removehopperlid.Fillyourhopperwiththematerialyou

plantospray.Donotexceed21/2gallons(b).

 5. SwitchyourunitONoncemoreandmakesurethatmaterialis

owingfromthereturntube.TurnpumpOFFandreplacethe

hopper lid.

Figure 10 - Releasing the Inlet Valve

If spray material does not ow from the return tube,

the inlet valve may be stuck. Follow these steps.

 1. ShuttheunitOFFandunplug.

 2. Carefullyremovethehopper.Cleantheconnectionarea

between the hopper and the basic unit.

3. Insert the inlet pusher tool (a) into the center of the inlet valve

area(b).Thisshouldreleasetheinletvalveandallowspraying

material to ow through the return tube.

4. Replace hopper and return tube and resume.

Project 115

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Comments to this Manuals

No comments

WAGNER Project 115 Owner's Manual Page 9

Comments to this Manuals

Related products and manuals for Power tools WAGNER Project 115